Showing results: 511 - 525 of 5217 items found.
-
C8900 -
Chroma Systems Solutions, Inc.
The 8900 electrical equipment ATS can complete measurement and test procedures simultaneously and automatically. This automated functionality decreases the risk of errors due to improperly written tests. Chroma 8900 solves the Electrical Safety Test and special FUNCTION test solution.
-
CTTS Series -
Shanghai Jiuzhi Electric Co., Ltd.
CTT series cable test terminations are used to test Plastic insulated high-voltage cables. The specific advantages of this series versus conventional terminations are fast and convenient assembly. The terminations can be used for partial discharge (PD) measurements, impulse voltage testing, loss factor (tan delta) measurements and, if the cable ends are carefully prepared, for breakdown testing (step test).
-
Cincinnati Test Systems
Vacuum leak testing is the principal leak test method for testing parts that could have leakage from an external source into their housings and casings. Parts like underwater sensors or housings, outdoor electrical housings, sealed components, and components associated with vacuum sources are all prime candidates for vacuum leak testing. Operation of instruments that supply vacuum to test parts instead of pressure works in a similar, yet essentially opposite, manner as pressure decay testing.
-
Premier Electrosystems
Premier Electrosystems' Thermal Stability Test Setup is used to test thermoplastics and PVC (Plasticized Polyvinyl Chloride) materials. When exposed to continuous heat, these materials degenerate and emit harmful acidic gases. The instrument is manufactured for testing PVC materials for their thermal stability at higher temperature.
-
G-3 Series -
Shinken Co. LTD.
This series was used for the special structure of airbearing guide of inspection for Seismic Detectors andcharacterized is large displacement and high-accuracywaveform. In addition, the use of the Windows seismicdetector controller is easy to operate it.
-
i-series -
IMV Corporation
Vibration tests have become diversified and specifications have become increasingly strict.i-series offer a user-friendly lineup with enhanced performance and durability.
-
WonATech Co.,Ltd
For 100Watt DMFC single cell testCompact sizeConsists of electronic load, gas/liquid controller, humidifier and methanol pump etc.
-
LD-LGST-A10 -
Labodam
Gel Strength Test SystemLD-LGST-A10is mainly used to measure the gel strength of gelatine under the stipulated environment. It has traveling accuracy ± 0.3 % and Test range up to 5 to 1000 g Bloom. It consists of Jelly Strength Tester, Constant Temperature Bath and Refrigerator. Sampling depth can be present arbitrarily in 1 to 60 mm. It consists four kinds of sampling measurement modes: single-step, maintaining, circulating and automatic.
-
UI2000-ET -
Lisun Electronics Inc.
• Input characteristics analysis 1) Measure Vrms (10-300V) Lrms (0.04-4A) W, PF, Hz, total harmonic and 0-50 component of harmonic 2) Accuracy: ± (0.4%reading + 0.1%range + 1digit) • Output characteristics analysis 1) Measure lamp voltage (1-60V) lamp current (03-20A) lamp power, crest factor and oscillatory frequency 2) Accuracy: Class 2 • It can print without compute, and provide the communication port for PC
-
DC-series -
IMV Corporation
Depending on the reference PSD or other operating conditions such as the specimen, one part of the controlled response may deviate from the reference PSD
-
CV-series -
IMV Corporation
CV-series is suitable for transportation tests. The lateral support stiffness and maximum displacement of the CV-series are large enough to be accommodate vibration tests of the specimens with high center of gravity.
-
DU-7211 -
Delta United Instrument Co., Ltd.
Inductance, Q factor, Leakage Inductance, AC Resistance, Capacitance, DC Resistance, Balance,Turn ratio, Open/Short check
-
-
FRANKONIA GmbH
Conducted RF immunity tests acc. to IEC/EN61000-4-6 and BCI tests acc. to ISO 11452-4 and MIL-STD 461 CS 114 Signal generator,RF-power amplifier, RF-power meter and directional coupler (optional) in one 19”-caseStand-alone operation possible with optional available netbookControl-software includedMost important parameters are shown on an integrated displayAutomatic EUT-monitoringOperation via USB port of a PC or NotebookComplete range of CDNs available
-
MTO -
Flynn Systems Corp.
The MTO restricts access to test development and test files, yet enables users to run any predeveloped onTAP boundary scan / JTAG tests, including memory cluster tests and Flash programming, when activated. The MTO also provides access to ProScan, the graphical debugging environment for onTAP. Users have access to accurate pin-level diagnostics and debug features, such as the netlist browser, test reports, and low-level pin access for toggling pins, to speed up the manufacturing process and ensure accuracy.